Piston

Music Home >> Music Genres >> Undetermined Music



< < < < < > > > > > More Info on Piston Similar Undetermined Music Search Artistopia

Biography

A piston is a component of reciprocating engine s, reciprocating pump s, gas compressor s and pneumatic cylinder s, among other similar mechanisms. It is the moving component that is contained by a Cylinder (engine)|cylinder and is made gas-tight by piston ring s. In an engine, its purpose is to transfer force from expanding gas in the cylinder to the crankshaft via a piston rod and/or connecting rod . In a pump, the function is reversed and force is transferred from the crankshaft to the piston for the purpose of compressing or ejecting the fluid in the cylinder. In some engines, the piston also acts as a valve by covering and uncovering Porting_%28engine%29#Two-stroke porting|port s in the cylinder wall.

Piston engines

Internal combustion engines

The piston of an internal combustion piston engine|internal combustion engine is acted upon by the pressure of the expanding combustion gases in the combustion chamber space at the top of the cylinder. This force then acts downwards through the connecting rod and onto the crankshaft . The connecting rod is attached to the piston by a swivelling gudgeon pin (US: wrist pin). This pin is mounted within the piston: unlike the steam engine, there is no piston rod or crosshead .

The pin itself is of hardened steel and is fixed in the piston, but free to move in the connecting rod. A few designs use a 'fully floating' design that is loose in both components. All pins must be prevented from moving sideways and the ends of the pin digging into the cylinder wall, usually by circlip s.

Gas sealing is achieved by the use of piston ring s. These are a number of narrow iron rings, fitted loosely into grooves in the piston, just below the crown. The rings are split at a point in the rim, allowing them to press against the cylinder with a light spring pressure. Two types of ring are used: the upper rings have solid faces and provide gas sealing; lower rings have narrow edges and a U-shaped profile, to act as oil scrapers. There are many proprietary and detail design features associated with piston rings.

Pistons are casting (metalworking)|cast from aluminium alloy s. For better strength and fatigue life, some racing pistons may be forging|forged instead. Early pistons were of cast iron , but there were obvious benefits for engine balancing if a lighter alloy could be used. To produce pistons that could survive engine combustion temperatures, it was necessary to develop new alloys such as Y alloy and Hiduminium , specifically for use as pistons.

A few early gas engine s'Gas' here refers to a fuel gas , not gasoline . had double-acting cylinder s, but otherwise effectively all internal combustion engine pistons are single-acting cylinder|single-acting . During World War II , the US submarine USS Pompano (SS-181)| Pompano A handful of submarines in the following class used a similar engine, with almost equally poor results. was fitted with a prototype of the infamously unreliable Hooven-Owens-Rentschler|H.O.R. double-acting two-stroke diesel engine. Although compact, for use in a cramped submarine, this design of engine was not repeated.

Trunk pistons

Trunk pistons are long, relative to their diameter. They act as both piston and also as a cylindrical crosshead. As the connecting rod is angled for part of its rotation, there is also a side force that reacts along the side of the piston against the cylinder wall. A longer piston helps to support this.

Trunk pistons have been a common design of piston since the early days of the reciprocating internal combustion engine. They were used for both petrol and diesel engines, although high speed engines have now adopted the lighter weight #Slipper piston|slipper piston .

A characteristic of most trunk pistons, particularly for diesel engines, is that they have a groove for an oil ring below the gudgeon pin, not just the rings between the gudgeon pin and crown.

The name 'trunk piston' derives from the ' trunk engine ', an early design of marine steam engine . To make these more compact, they avoided the steam engine's usual piston rod and separate crosshead and were instead the first engine design to place the gudgeon pin directly within the piston. Otherwise these trunk engine pistons bore little resemblance to the trunk piston: they were of extremely large diameter and were double-acting. Their 'trunk' was a narrow cylinder placed mounted in the centre of this piston.

Crosshead pistons

Large slow-speed Diesel engines may require additional support for the side forces on the piston. These engines typically use crosshead pistons. The main piston has a large piston rod extending downwards from the piston to what is effectively a second smaller-diameter piston. The main piston is responsible for gas sealing and carries the piston rings. The smaller piston is purely a mechanical guide. It runs within a small cylinder as a trunk guide and also carries the gudgeon pin.

Because of the additional weight of these pistons, they are not used for high-speed engines.

Slipper pistons

A slipper piston is a piston for a petrol engine that has been reduced in size and weight as much as possible. In the extreme case, they are reduced to the piston crown, support for the piston rings, and just enough of the piston skirt remaining to leave two lands so as to stop the piston rocking in the bore. The sides of the piston skirt around the gudgeon pin are reduced away from the cylinder wall. The purpose is mostly to reduce the reciprocating mass, thus making it easier to balance the engine and so permit high speeds. A secondary benefit may be some reduction in friction with the cylinder wall, however as most of this is due to the parts of the piston that are left behind, the benefit is minor.

Deflector pistons

Deflector pistons are used in two-stroke engine s with crankcase compression, where the gas flow within the cylinder must be carefully directed in order to provide efficient scavenging (automotive)|scavenging . With cross scavenging , the transfer (inlet to the cylinder) and exhaust ports are on directly facing sides of the cylinder wall. To prevent the incoming mixture passing straight across from one port to the other, the piston has a raised rib on its crown. This is intended to deflect the incoming mixture upwards, around the combustion chamber . Much effort, and many different designs of piston crown, went into developing improved scavenging. The crowns developed from a simple rib to a large asymmetric bulge, usually with a steep face on the inlet side and a gentle curve on the exhaust. Despite this, cross scavenging was never as effective as hoped. Most engines today use Schnuerle porting instead. This places a pair of transfer ports in the sides of the cylinder and encourages gas flow to rotate around a vertical axis, rather than a horizontal axis.

Steam engines

Steam engine s are usually double-acting (i.e. steam pressure acts alternately on each side of the piston) and the admission and release of steam is controlled by D slide valve|slide valves , piston valve s or poppet valve s. Consequently, steam engine pistons are nearly always comparatively thin discs: their diameter is several times their thickness. (One exception is the trunk engine piston, shaped more like those in a modern internal-combustion engine.)

Pumps

Piston pumps can be used to move liquid s or compress gas es.

For liquids

For gases

Air cannons

There are two special type of pistons used in air cannon s: close tolerance pistons and double pistons. While in close tolerance pistons, O-ring s serve as a valve, O-rings are not used in in double piston types.

Close-tolerance pistons have a number of disadvantages: They can swell and stick, their properties alter due to atmospheric changes, and they fit tightly in the cylinder with close tolerances. Backlash may suck some of the bin material into the valve which can cause the piston to stick.

Common features of double piston construction: They cannot swell and stick, they fit loosely in the cylinder (no tight tolerances), atmospheric changes do not affect them, and foreign material entering the cylinder doesn't cause sticking.

Drawbacks

Since the piston is the main reciprocating part of an engine, its movement creates an imbalance. This imbalance generally manifests itself as a vibration, which causes the engine to be perceivably harsh. The friction between the walls of the cylinder and the piston rings eventually results in wear, reducing the effective life of the mechanism.

The sound generated by a reciprocating engine can be intolerable and as a result, many reciprocating engines rely on heavy noise suppression equipment to diminish droning and loudness. To transmit the energy of the piston to the crank, the piston is connected to a connecting rod which is in turn connected to the crank. Because the linear movement of the piston must be converted to a rotational movement of the crank, mechanical loss is experienced as a consequence. Overall, this leads to a decrease in the overall efficiency of the combustion process. The motion of the crank shaft is not smooth, since energy supplied by the piston is not continuous and it is impulsive in nature. To address this, manufacturers fit heavy flywheels which supply constant inertia to the crank. Balance shafts are also fitted to some engines, and diminish the instability generated by the piston's movement.

Copyright Citations

This article is licensed under the GNU License
Click here for original article: Piston


1. Clutch 2. Horsepower 3. Allen Iverson 4. Supercharger 5. Shane Lynch 6. Leonard Bernstein 7. Walter Piston 8. L.u.n.g.s. 9. Airbag 10. Amy Carlson 11. Aviation 12. Drill 13. Fifteen 14. G-5 15. Glueleg 16. Gun 17. guns 18. Hombres G 19. Hone 20. Kobe Bryant 21. Lambretta 22. Locomotive Breath 23. Machine Gun 24. Magneto 25. Mar De Copas

Undetermined Music Artists